- #Uniextract 08.exe download install
- #Uniextract 08.exe download upgrade
- #Uniextract 08.exe download free
#Uniextract 08.exe download install
Needed: Copy of Windows XP, the Sony SATA drivers from the site above, nLite, CD/DVD burnerġ) Go to the Sony drivers site linked at the top of this thread and download “Intel® SATA Driver for Microsoft® Windows® XP Operating System” under the “Hard Drive” category.Ģ) Unzip the drivers to a folder of your choice.ģ) Download and install a copy of nLite (it’s free).Ĥ) Create a folder on your hard drive where the slipstreamed version of Windows is going to go.ĥ) Insert your Windows XP CD into your ROM drive and open nLite.ħ) Click Browse, and select your ROM drive or folder with the Windows install files, then when you are prompted, select the folder where you want the files to be copied (the folder created in step four) and nLite will begin copying your files, the process should only take about six minutes.Ĩ) When complete, just hit “Next” on the “Locating the Windows installation (top left corner)” screen, then hit “Next” again on the “Presets” screen so you end up on the “Task Selection” screen. Slipstreaming SATA drivers is not difficult. Luckily Sony provides the SATA drivers, but you will need to create yourself a copy of Windows XP with the SATA drivers on them to successfully install XP. Since the FWs have SATA hard drives, Windows XP cannot recognize them natively. Remove these screws, then put in your new hard drive, and screw the new hard drive into the cage.Ħ) Reinsert the cage into the laptop, slide it to the right to cleanly engage the hard drive into the laptop, screw in the three screws which were removed in step two, and then screw back on the hard drive panel, and you should be all set. The tab itself can be seen clearly in the picture in step five below.ĥ) Once you have the hard drive cage outside of the laptop, there are four screws which need to be removed, two on each side. This tab allows you to pull the hard drive up out of the laptop, but be carful and only pull it up just enough to pull the hard drive cage out on an angle to the right because there is a piece of metal that goes into the laptop when you slide the cage to the right in step three that will bend if you pull the hard drive cage up too much. This will disengage the hard drive from the FW and allow you to remove it.Ĥ) There is a plastic tab on the back of the hard drive between the two screws.
Gently take these three screws out.ģ) Once the three screws have been removed, gently slide the hard drive cage all the way to the left. You’ll need to remove one screw here and take off the hard drive panel.Ģ) After the panel is removed, there are three screws which need to be removed. I purchased this kit from Amazon and the smallest Phillips head screw driver worked perfectly ($8.49 at time of this post).ģ: Actually changing the hard drive is pretty easy.ġ) Flip your FW on its back, the hard drive is located on the bottom left hand side.
#Uniextract 08.exe download free
WD Scorpio Black (With free-fall sensor) (320 GB, 3 Gb/s, 16 MB Cache, 7200 RPM)īuy.com is the cheapest place to buy the drive ($97.24 at the time of this post, with free shipping).Ĭlick on the link below to get an additional 5% off the drive.Ĭlick on redeem coupon, then place the hard drive in your cart, and the discount should be applied to the hard drive.Ģ: Another product you may need to purchase is a small tool kit.
#Uniextract 08.exe download upgrade
If you are looking to upgrade your hard drive, I recommend this drive. I bought this drive for $99, and I basically got a 160GB 5400rpm drive from Sony for free. For the same $99, you can buy what is arguably considered the best notebook hard drive currently on the market, the Western Digital Scorpio Black Edition, 320GB 7200rpm hard drive with free fall sensor. I knew it would probably be a generic brand hard drive, so I decided to buy a hard drive aftermarket.
Need: Small Phillips head screw drive, notebook SATA hard driveġ: While I was configuring my FW190, I knew I wanted a 7200rpm hard drive, but Sony wanted $99 to upgrade to the cheapest 7200rpm hard drive, which happened to be 200GB. Step One - Changing the Internal SATA Hard Drive (Optional): Thank you to PhilFlow, as I used his guide to XP on a Vaio Z as a basis for my guide. A friend of mine bought a FW290 and I was successfully able to install XP on his 290 as well, it’s a bit more complicated, but if you follow these steps, you should have a fully functioning FW190/290 with Windows XP by the time you are done.
I finally did it and everything works great except some of the FN keys which there still isn’t a solution for. After searching this forum and posting in several threads, I was still left with many questions about putting XP on my FW190. Many of us still prefer Windows XP to Windows Vista.
0 kommentar(er)
